The First Stage: Material Selection & Billet Preparation
Material Selection: The preferred titanium alloy grade is TC4 (Ti-6Al-4V), which is the best due to its comprehensive properties (strength, toughness, corrosion resistance, machinability). Depending on specific needs (e.g., cost, higher plasticity), pure titanium (TA1, TA2) or other near-α/near-β alloys may also be used.
Raw Material Form: Titanium alloy strip coils or plates that meet the specifications are mainly used. The width and thickness of the strip are precisely selected according to the inner diameter and clamping force requirements of the clamp design, and the thickness range is usually 0.5mm - 2.0mm.
Unwinding & Leveling: The strip coil is uncoiled on specialized equipment, and the internal stress caused by crimping is eliminated by a precision leveling machine, ensuring that the strip meets the flatness requirements required for subsequent stamping.
Precision punching and blanking: Use high-tonnage, high-precision punching machines with specially designed progressive dies or composite dies for continuous stamping.
The Main Blanking Processes Include:
Blanking Profile: The basic long strip profile after punching out the clamp unfolds, which may contain pre-formed features at both ends.
Punching: Punching through holes for attaching fasteners (bolts/nuts), usually long or round holes.
Cut/Stamp: Make small cuts at specific locations (in preparation for subsequent bending) or imprint marks (e.g., part number, production batch).
Key Points: The mold design must accurately consider the characteristics of titanium alloy (high strength, easy to cold hardening) and optimize the mold gap; The cutting edge should be made of high-hardness, high-wear-resistant materials and kept sharp; Specialized lubricants are often required to reduce friction, reduce punching forces and burrs, and prevent over-hardening of the material.
The Second Stage: Molding & Processing
Pre-Forming : For more complex clamp designs (such as special end shapes), a pre-forming process may be added before the main body is bent, and a special mold is used to complete the partial shaping on the punch or press.
Bending Of The V-Shaped Body : This step is the key to forming the V-shaped structure of the clamp core, and the low elastic modulus and large rebound of titanium alloys (especially TC4) are the main challenges.
Main Forming Methods: Cold forming + bending compensation: carried out in a precision press brake or mold cavity.
Core Strategy: Based on material property data and a large number of tests, accurately calculate and design a bending angle significantly larger than the target angle, and use the huge rebound characteristics of titanium alloy to make it exactly reach the required angle after unloading.
The bending radius, down-pressure speed, holding time, and pressure need to be controlled extremely precisely.
Pros: High efficiency and relatively low cost.
Disadvantages: Accuracy control is extremely difficult, residual stress is high, which may affect fatigue life and long-term shape stability; This method may not work for thicker materials or higher strength grades.
Thermoforming :It is performed in a closed chamber or vacuum furnace filled with an inert shielding gas such as argon.
The titanium strip is heated below the recrystallization temperature and above the plastic deformation zone (for TC4, it is usually precisely controlled in the range of 500°C - 800°C).
At this temperature, the yield strength of titanium alloy is significantly reduced, the plasticity is improved, and the rebound is greatly reduced.
It is bent and molded in a heated state, and after molding, it is usually cooled slowly in a protective atmosphere or controlled by temperature.
Advantages: It can effectively overcome rebound, can form thicker or higher strength materials, and has low residual stress.
Disadvantages: High equipment investment and operating costs (heating, protecting the atmosphere), long production cycles, strict temperature control to prevent oxidation and grain growth.
End Forming: Accurately bend or crimp the lap joints at both ends of the clamp to ensure it fits smoothly with the bolt/nut and withstands locking forces. Rebound also needs to be considered.
The Third Stage: Heat Treatment
Stress Relief Annealing:
Objective: To eliminate residual stresses generated during cold forming or hot forming, and improve dimensional stability, fatigue resistance, and stress corrosion resistance.
Process: The formed clamp is placed in a vacuum furnace or inert atmosphere protection furnace, heated to an appropriate temperature (TC4 is usually 650°C - 750°C), kept warm for a certain period of time, and then cooled or slowly cooled with the furnace.
Key Points: Strictly control temperature, holding time, and cooling speed to avoid oxidation and contamination. Protecting the atmosphere (argon) or vacuum environment is critical.
The Fourth Stage: Surface Treatment
Cleaning: Thoroughly remove oil, lubricant residue, and oxides from the surface of the clamp.
Pickling: Specific acid solutions (e.g., nitric acid + hydrofluoric acid mixtures) are used to remove the oxide scale and oxygen-rich α layers formed during heat treatment or processing.
Key Points: Strictly control the acid concentration, temperature and time to prevent excessive corrosion. Operation should be carried out in well-ventilated or specialized equipment.
Sandblasting:
Abrasives of specific particle size and material (e.g., alumina, glass beads) are used for sandblasting.
Purpose: To obtain a uniform and consistent matte surface, improve subsequent coating adhesion, or simply as a final appearance treatment.
Anodizing :
Objective: To generate a dense, hard, and highly adhesive oxide film (TiO₂) on the surface of titanium, which significantly improves wear resistance, corrosion resistance, electrical insulation, and can provide a variety of decorative colors (through the interference color principle).
Process: The clamp acts as an anode and is immersed in a specific electrolyte (such as phosphate, chromate, or other environmentally friendly electrolyte) for electrolytic oxidation under precisely controlled voltage, current density, temperature, and time.
Key Points: Tightly control process parameters to achieve desired film thickness, color, and performance. The color of the film layer is directly related to the thickness of the film. This is one of the key advantages that distinguishes titanium clamps from steel clamps.
The Fifth Stage:Assembly, Inspection & Packaging
Assembly Fasteners:
Install the required bolts (or screws) and nuts (usually self-locking nuts, such as nylon insert nuts, all-metal lock nuts) into the reserved holes of the clamps.
Ensure that the bolt slides smoothly through the hole and that the nut can be securely locked.
Final Inspection:
Dimensional inspection: Use calipers, projectors, pass gauges, etc. to inspect critical dimensions (inner diameter, angle, hole position, thickness, width, etc.).
Visual inspection: Check the quality of the surface treatment (color uniformity, no scratches, no oxidation, no pollution).
Mechanical Property Sampling Inspection: Clamping force test, fatigue life test, elastic recovery test, etc. are carried out on batch products.
Corrosion Resistance Sampling: Salt spray test may be performed, etc.
Torque Testing: Tests the bolt's performance when tightened to the specified torque.
Cleaning & Rust Prevention: Thoroughly clean the surface of the clamp and apply a small amount of anti-rust oil if necessary (compatibility needs to be confirmed with the customer).
Packaging: Packaging (such as bags, boxes, plates) according to customer requirements, and clearly labeling product information, batch number, etc.
Overall, the manufacturing of titanium V-clamps is a complex process that incorporates material science, precision stamping, special forming, heat treatment, and surface treatment techniques. The core challenge is to overcome the high strength, low thermal conductivity, large rebound, and high temperature oxidation tendency of titanium alloys, especially TC4, to ensure that the final product meets the automotive industry's stringent requirements for clamping force, elasticity, corrosion resistance, fatigue life, and reliability through carefully designed processes such as thermoforming, precise bending compensation, protective atmosphere heat treatment, and precision anodizing. For more information, please contact catherine@hiriger.com.
